Installation of a hydromassage bath
The main structural elements of a hydromassage bath are represented by the body, as well as the installed equipment, the main unit of which is a fairly powerful electric pump, which is responsible for the uninterrupted circular circulation of water.
The main elements of equipment for a bathtub equipped with a hydromassage function include several devices presented
- nozzles that form and direct water jets;
- check valves that prevent water from flowing in the opposite direction;
- a compressor responsible for supplying air masses into the system;
- a thermostat that controls the temperature of the water.
Calibrated holes or nozzles are equipped with special linings, which can be made of plastic or metal.
Particular attention is paid to pumping equipment, the power indicators of which affect not only the amount of water pressure, but also the cost of the hot tub.
How to clean your pipe yourself
A Jacuzzi massage system consists of a pump and a set of pipes that supply water to a container. With prolonged use, they become covered with plaque and biofilms, which cannot always be removed using household chemicals.
To check and service the hydromassage system you must:
- remove the screen that covers the space under the bathtub;
- study the dismantling instructions, photograph or write down the order of connecting the tubes;
- loosen the nuts and remove the hoses where possible;
- wash the dismantled parts with running water, rinse the internal dirt filters;
- if the inner surface of the tubes remains slippery, soak them in a special solution for a Jacuzzi, and then clean them with a brush;
- reassemble the system in reverse order;
- Check the tightness of the connections by wrapping them in toilet paper and turning on the hydromassage.
Remove the screen and wash the dismantled parts.
If individual tubes are very clogged, you can clear them using a thick wire wrapped in damp gauze.
Main causes of breakdowns
Specialists in the repair of hydromassage structures note a number of the most common breakdowns that occur due to:
- blockages in main communications;
- formation of cracks, chips or scratches on the surface;
- failure of pumping equipment;
- failure of devices represented by water collectors, aero compressors and nozzles.
Before starting repair work, it is necessary to correctly determine the cause and the most effective way to correct it.
Breakage of the bathtub can be represented by the use of chemicals that are not recommended for cleaning the system, aggressive and destructive detergents, as well as low quality water characteristics and improper care of the plumbing fixture.
Specialists who will repair a hot tub in Moscow
If we talk about the repair of hot tubs, Moscow has one of the largest selection of providers of such services in Russia. Our craftsmen in Moscow can patch the Jacuzzi cover, clean the nozzles, replace the filter or control unit.
In general, in such a big city as Moscow there are many companies that repair Jacuzzis. However, when choosing someone who is comfortable entrusting a valuable plumbing fixture – a whirlpool bathtub – it is important to take into account professionalism and price. Companies that repair Jacuzzis in Moscow set rather high prices for their work.
Masters from our company will quickly arrive in any area of the city, be it an address on Mira Avenue or even somewhere on Zhukov Avenue. Speed is not the only advantage of our craftsmen; they can easily repair a jacuzzi in Moscow not only cheaply, but also with high quality.
In order to order professional repair of a jacuzzi in Moscow, you just need to call the team from the “Plumbers Service” by calling the number.
General rules for repairing hot tubs
As practice shows, self-repair of a bathtub with hydromassage equipment is advisable only if free service and repairs in a special center are impossible. You can fix it yourself:
- cracks, chips and scratches;
- clogged drain;
- presence of limescale;
- breakdown of the air compressor;
- incorrect pump operation;
- failure of injectors;
- sticking of the pneumatic button;
- problems associated with the water collector.
Acrylic bathtub repair
Initially, you should correctly determine the cause of the breakdown. Most often, blockages or failures of the cartridge are detected, so sometimes it is enough to simply remove this part from the device and clean it, but in some cases it will be necessary to completely replace the devices.
Excessive water pressure may be the result of clogged supply filters, but before you start cleaning, you need to check the pressure in the main pipeline.
Removing blockages
As a rule, household Jacuzzis cease to fulfill their functional load as a result of blockages. In this case, the cartridge is initially cleaned, and then the entire system.
Performing such an operation independently is not too difficult, but directly depends on the characteristics of the system.
If you have hydromassage equipment equipped with a built-in disinfection unit, a special cleaning agent is poured in that can independently remove blockages formed inside the pipe. If there is no self-cleaning system, then it is advisable to use cleaning tablets immersed directly in water when operating the hydromassage equipment.
Prevention of clogging of a hot tub is to prevent threads and hair, organic fibers and wool from getting into the bowl of the sanitary fixture.
Basic rules for performing repair work
If the warranty period has expired and your product has broken down, do not rush to call a repairman. The fact is that it is possible to repair a jacuzzi with your own hands .
All that is necessary for this is to calculate the reason.
Most often, the cartridge .
In this case, it is enough to clean it, but replacement may be required. Not very strong water pressure proves that the system filters are dirty . To check the pressure power, you need to open all the taps in the house.
When replacing a broken part, you must buy a similar spare part from the Jacuzzi manufacturer. This is due to the fact that analogues from other companies may differ significantly in various ways, that is, their use can lead to malfunction of the entire hydromassage system.
As a rule, the bathtub stops functioning due to blockages. In order to eliminate them, as well as prevent them, detergent is poured into a specially designated hole for cleaning bathtubs (hydromassage baths). After passing through all the pipes, it destroys all the dirt, directing it into the sewer. This saves the device from destruction.
In devices without a disinfection system, to clear the blockage, you can use
a cleaning tablet and throw it into the water while using the bath.
In areas with poor quality water, a similar procedure should be carried out at least once every two months. In order to prevent blockages, we must remember that hair, threads and other foreign substances should not get into the Jacuzzi device, since over time this will invariably lead to blockage. In addition, we must not forget that to clean acrylic products, it is necessary to use only specialized solutions and tablets.
Elimination of shallow and through cracks
As a rule, during operation, the owner of a bathtub encounters the formation of not only shallow or superficial, but also so-called through cracks in the sanitary ware.
To eliminate them, you need to perform the following, not too complicated, measures:
- The technology for eliminating shallow chips involves initially expanding the damage itself with sandpaper, and then performing high-quality degreasing and applying an acrylic mixture, followed by removing the excess mixture with emery and sanding.
- If you have a special repair kit, which many manufacturers supplement their products with, surface cracks can be eliminated very easily and simply. If the plumbing equipment is made by injection molding, then it is advisable to use liquid acrylic to eliminate small and shallow cracks.
- Through chips and cracks are more complex, growing most often in two directions. In this case, in order to prevent further increase in size of the damage, you need to drill holes with a thin drill at a couple of points of the crack farthest from the center, and then degrease the surface.
Deep or through cracks must be sealed with adhesive tape, and only after that they are treated with liquid acrylic.
Despite some differences, independent removal of shallow and through cracks in the bowl requires the obligatory implementation of such actions as degreasing, “clogging” with acrylic mass and grinding.
Have you decided to install a jacuzzi in your apartment? An acrylic whirlpool bathtub is a good choice for those who value quality and design.
We’ll talk about the effectiveness of a hydromassage mat as an alternative to a hot tub here.
Did you know that hydromassage is not for everyone? Read about the health benefits and harms of the procedure in the following material.
Replacing the mixer
The main reason for replacing the faucet is damage to the cartridge. Quite often, such an element of hydromassage equipment can simply be cleaned, which allows you to completely restore the functionality of the plumbing fixture.
If the desired effect as a result of cleaning is not achieved, then the cartridge is dismantled and completely replaced.
Built-in faucet in the bathroom
Before installing an element such as a cartridge, it is very important to thoroughly clean the installation area, completely removing all remaining scale or water.
What to do if the mixer or nozzle is faulty?
If a cartridge breaks, it needs to be cleaned, but if this action does not give any result, then you need to purchase exactly the same, new one. When installing it, the nest is treated, to do this, remove the deposited scale and wipe it dry.
If the nozzle becomes clogged, then water comes out in a small stream. To clean this element, unscrew the cap and use a soft cloth and water to remove dirt.
We looked at how to repair Jacuzzi bathtubs yourself, but you need to know that after eliminating existing faults, you need to configure the equipment. If they don’t know how to do this, then they turn to specialists for help who will do all the necessary work quickly and efficiently.
Injector malfunction
Most often, the main root cause of a bathtub with hydromassage equipment becoming unusable is clogged nozzles. In such a situation, there is a decrease in the power and pressure level of the water jet.
To independently correct this type of breakdown, you need to unscrew the cap and thoroughly but carefully clean the inner surface with a soft cloth and a water jet.
Hydromassage jets
If the nozzle has become completely unusable, then it is advisable to dismantle it and subsequently replace it with a device with a similar design.
Preventative care
To prevent breakdowns of a bathtub with hydromassage equipment, it is necessary to follow preventive measures:
- Rinse the surface of the bath bowl immediately after use;
- After rinsing, wipe the surface of the bowl with a soft, dry cloth.
For simple, regular cleaning of such plumbing equipment, you need to fill the bowl with water and disinfectant 50 mm above the top nozzles, then turn on the pumping equipment for five minutes and drain the water after a quarter of an hour.
The heavy cast iron bathtub is highly reliable. A cast iron hot tub will last for many years. The only drawback is the limited design of the models.
For tips from craftsmen on how to make a jacuzzi with your own hands, see this page.
At the final stage of cleaning, the bowl is filled with clean water, and the pumps are turned on for two to three minutes, after which the water is drained, the filters are dismantled, cleaned and returned to their place.
Professional maintenance of hot tubs is an expensive pleasure, so experts recommend strictly following the operating rules, as well as systematically performing preventive cleaning and disinfection of such equipment.
Final system disinfection
With regular maintenance, the system is disinfected simultaneously with monthly cleaning. In case of severe contamination, longer exposure to antiseptics is required to destroy fungi and bacteria.
Algorithm for disinfecting a hot tub:
- wash the surface of the bathtub and the guide elements with liquid soap or a product for the appropriate type of surface;
- fill the bath with hot water (+40...+45°C) so that its level is 5-10 cm above the nozzles;
- add 200-300 ml of detergent to the container to disinfect the jacuzzi;
- turn on the hydromassage at maximum power for 15-20 minutes;
- let the solution stand for 25-30 minutes;
- drain the liquid, refill the bath with cool water;
- turn on the massage for an additional 5-7 minutes;
- empty the container, wash its walls with a soft sponge and wipe dry.
Some hot tub models have a self-cleaning mode. If this function is available, the disinfectant liquid is poured into a special hole in the wall of the bathtub.
The following products are suitable for killing fungi and bacteria:
- "Wonder Worker Hot Tub";
- "Bagi Jacuzzi";
- Triton Disinfectant;
- Relisan.
