Is it possible to drill, trim or saw an acrylic bathtub?

Ways to get out of the situation

Firstly, it should be clarified that reducing the bathtub is radical, but it is not the only way to solve the problem. The following points are worth considering.

Make a groove in the wall for the bathtub. An excellent way out of the situation, the bathroom will gain additional support from the side, and the structure will become much more rigid. But this method is very dirty, and is only possible if the tiles were not enclosed, since cutting the laid ceramics is a big risk. A load-bearing wall can also become an obstacle; It is strictly forbidden to make horizontal grooves in it.

If the above methods do not suit you, there is nothing left to do but cut out the bathtub. We will look at how to do this correctly and with less losses below.

Underwater rocks

What to do after the sawing work has been carried out and how to protect yourself from possible negative consequences?

Due to a decrease in the rigidity of the edge on the cut side, during operation there may be some disruption of the bathtub geometry, as experts call LED. In this case, experienced craftsmen advise installing the bathtub on standard legs and on a durable frame.
The required edge stiffness can be restored using the fiberglass repair kit and epoxy bumper mentioned above. You need to glue them not with a cut, but with the inner surface of the fold of the edge of the bathtub, by 1-2 centimeters. This will help create additional edge support.
Can be attached to the wall from the undercut side, aluminum profile or wooden block. The side of the tub will rest on them. This will increase the rigidity of the entire structure.

It's worth remembering that cutting the bath will void your warranty. Unfortunately, nothing can be done about this.

The gap between the wall and the bathtub and the choice of border

If the bathtub was installed after finishing the walls, a gap will inevitably remain between its side and the wall. Large or not very much depends on how smooth the walls are and whether the bathtub itself is level. In any case, it is better to seal this gap. Firstly, there will be no dampness under the bathtub, and secondly, the appearance is better.

To choose a border for a bathtub, you need to proceed from the width of the gap. Depending on the distance to the wall, the installation sequence changes:

If the distance between the bathtub and the wall is up to 3 cm, you can immediately install the side. Only its bottom shelf should be wide - it should be 3 times wider than the slot. And one more thing - in this case, only hard corners - ceramic or plastic - are suitable. It is better to glue the border tape with a small gap of a few millimeters or pre-seal it with a cement-sand mixture.
If the distance from the side to the bathtub is more than 3 cm, it must first be sealed. There are three options: Attach the formwork from below, fill it with concrete, after setting (at least three to four days) you can continue work.
Cover the gap with moisture-resistant plasterboard in two layers. A frame is assembled, which is attached to the wall with dowels, and to the bathtub - with mounting foam or liquid nails. If the shelf turns out to be large, install vertical supports. In general, a full-fledged frame is assembled. You can mount a corner or ceramic tile on the fixed drywall if the gap is very large and the width of the corner is not enough to close it.
Make a side from the same tiles as the walls. The option is familiar from past years, but today it is no longer popular.
Assemble a frame from a metal profile and cover it with moisture-resistant plasterboard. You can combine it with a frame for a bathtub screen

Having decided on the technology for sealing the gap, you can choose a border for the bathtub. It's not as easy as it seems - there are many different options, so you can get lost.

Read here how to restore the cover of an old bathtub.

How to shorten it correctly?

If you still decide to remove a few centimeters from your bathtub, you should read the instructions below:

Take all measurements carefully and decide exactly how much to cut. Measure the cut seven times just for this.
Cover the surface where the cut will be made with masking tape. This will prevent cracks and chips from appearing, and it will be more convenient to mark on it.
Carefully and slowly mark the future cut. Draw the line of the cut with a felt-tip pen or felt-tip pen.

Can it be cut to length?

A bathroom should never be cut to length. Therefore, you will definitely greatly violate the rigidity of the structure, and the font will probably burst over time. It’s better to get out of this situation differently: make a strobe after all.

Is it worth cutting any material?

First you need to decide what material your bathtub is made of and whether it can be sawed. There are two main varieties:

Made from ABS plastic , they are produced using a very simplified technology. The acrylic layer is very thin, about 2 mm, essentially molded fiberglass painted with acrylic paint.
Made from cast acrylic , layer thickness from 5 mm, with the necessary antiseptic additives and reinforcement added.

Products made from cast acrylic last much longer than models made from ABS plastic. Some manufacturers provide a 15-year warranty on their products. During this time you will have to replace three cheap bathtubs, so the price of cast acrylic is completely justified. Such fonts cost from 12,000 rubles.

Baths of the first type do not last long and quickly lose their presentation. It is not advisable to cut such baths.

Cracks and scratches will certainly appear, and the structure will lose its rigidity. Bowls of the second type can be cut if done correctly.

How to shorten it correctly?

If you still decide to remove a few centimeters from your bathtub, you should read the instructions below:

Take all measurements carefully and decide exactly how much to cut. Measure the cut seven times just for this.
Cover the surface where the cut will be made with masking tape. This will prevent cracks and chips from appearing, and it will be more convenient to mark on it.
Carefully and slowly mark the future cut. Draw the line of the cut with a felt-tip pen or felt-tip pen.

Share with your friends:

Do-it-yourself puttying of walls under wallpaper Preparing plastered walls for processing is the most important stage of restoration work. This is not very difficult, so putting putty on the walls with your own hands for further painting or wallpaper will not be a problem.

How to choose metal entrance doors These days, understanding the huge range of entrance doors from different manufacturers is not easy. In this article we will tell you how to choose metal entrance doors to your apartment, taking into account all the nuances and requirements.

How to deal with fungus in the bathroom and why it is dangerous. A rather unpleasant surprise for any tenant would be to encounter fungus or mold in their own bathroom. People who have had to deal with them know that it can drag on for a long time and take a lot of effort.

READ How to Properly Set Up a Band Saw

Is it possible to glue wallpaper onto wallpaper on the ceiling or wall? It was decided to renovate the apartment, but I really don’t want to dilute the dirt, dust, and then wash it all. In this regard, the question arises quite reasonably: if the wallpaper on the walls or ceiling holds up well, can you stick the wallpaper on it again?

Perhaps the dimensions of the room were not taken correctly; the bathroom is longer and a little wider than we need.

Is it possible to somehow shorten (cut off) an acrylic bathtub, is it not worth it?

Technically, cutting an acrylic bathtub is not difficult.

Much simpler than, for example, cast iron.

But still I would not recommend doing this.

The rigidity of an acrylic bathtub is still not great.

This is several times worse than in a cast iron bath and much worse than in a steel bath.

By cutting the bathtub boards to length or width, you will loosen the entire structure as a whole.

Even if it is a high-quality acrylic bathtub (cast acrylic, plus fittings).

You have several ways out of the situation:

You cannot take a bath, install the bath according to a temporary scheme, make markings and then such strobes are made (cut) in the wall.

Gates can be made along the length of the side of the bathtub and along the short side.

If the bathtub does not fit in length, it is longer and much longer, then we make 2 strobe, on one side of the bathtub and on the other (in parallel).

The bathtub (sides) in the grooves is an additional fastening, that is, the entire bathtub will be installed more rigidly.

Of course, problems will arise during dismantling, but bathtubs have been used for decades and even acrylic, if you follow a number of certain rules during its operation.

If you still decide to cut, then first we make markings and mark the line with a marker.

Acrylic is easy to cut, you can use a hacksaw, you can use an electric jigsaw and fine tooth files for it.

You can even use a grinder, but the grinder needs a speed controller, for a grinder there is a cutting wheel for metal, we set the minimum speed.

Is it worth cutting any material?

First you need to decide what material your bathtub is made of and whether it can be sawed. There are two main varieties:

Made from ABS plastic , they are produced using a very simplified technology. The acrylic layer is very thin, about 2 mm, essentially molded fiberglass painted with acrylic paint.
Made from cast acrylic , layer thickness from 5 mm, with the necessary antiseptic additives and reinforcement added.

Baths of the first type do not last long and quickly lose their presentation. It is not advisable to cut such baths.

Cracks and scratches will certainly appear, and the structure will lose its rigidity. Bowls of the second type can be cut if done correctly.

Ways to get out of the situation

Firstly, it should be clarified that reducing the bathtub is radical, but it is not the only way to solve the problem. The following points are worth considering.

If the above methods do not suit you, there is nothing left to do but cut out the bathtub. We will look at how to do this correctly and with less losses below.

Acrylic bath

You can cut 2cm from the end of the bathtub (acrylic) to make it fit, what are the implications for the plastic? Peels off, etc.

Where are you all going to put your ACRYLIC bathtub? If it was cast iron, then no problem. Acrylic bathtubs were cut, and more than once. Nothing will happen to plastic. The only thing that needs to be restored before installing the cut-off bathtub is to attach, for example, an aluminum corner to the wall. All

Is there a better way to sand a wall?

I think so too, especially since the end is usually rounded down, forming a rigidity

I would advise not to experiment. If you can't dive into the wall, try asking your question directly to the manufacturer.

I completely agree with you. Anything that can be cut off. Only then can the consequences be dire.

Of course, you can cut more than once. But, you need to think in advance, maybe you should cut off one centimeter on both sides? You need to glue the corner of the border.

It’s better and more careful to screw it into the wall! Did you not lay tiles before installing the bathtub?

Perhaps, if you then cover it with a border or corners, the bath itself will not peel off or crack!

It is safer to grind, even if the tiles are laid out, a grinder with a diamond blade and off you go. On the side where the drain is, the curb tape will close, only you need to go to the silicone tape!

If Basco is LIGHT, the MOST way to direct her is to OPEN the bathhouse. DO NOT CUT, PICK UP THE FISH

Acrylic bathtubs should not be zipped into the gutter (read the installation instructions) because when the temperature expands there will be nowhere for it to go and it will crack.

Thank you for your competent advice, it’s a pity that I didn’t find your team earlier.

We and cast iron when they cut it. By the way, any bathtub can be cut off without consequences, well, in general, everything is correct.

Cut nothing will peel off, checked.

Can be cut off, only rigidity is lost

If you don't ruin her toughness

I agree with Vitalik Arkhipov. Cut more than once))

It’s better to cut a channel in the place on the wall where the bathtub rests with a small sander, 5 mm larger than the side of the bathtub, and then, like a bathtub, install either foam plastic or silicone sealant in the void.

Dear masters! If there was an opportunity and desire to install a bathtub without threads, then I would not raise the question, not for the first year after my husband.

You can cut off the bathtub, but what's the problem? Better to hit the wall. We put cast iron 1.50 in a room 1.48

Dimensions of an acrylic bathtub: characteristics and design choice

An acrylic bathtub has a long service life and good appearance. When choosing an acrylic bathtub, you always need to take into account several requirements and features.

After all, it will have to fit harmoniously into the space allocated to it and create comfortable conditions for water procedures for a long time. First of all, you need to pay attention to the design, quality and size of the bathroom.

Then you can select the appropriate plumbing fixtures so that everything becomes beautiful and harmonious, and can satisfy all your requirements.

Acrylic bathtubs have recently appeared in our everyday life. They provide structures with a smooth surface, minimal weight and are made of high-quality material.

They can have almost any shape and have virtually no disadvantages.

This design can be placed almost anywhere and selected exactly according to the dimensions that you need.

Acrylic bathtubs may vary in shape

Possible disadvantages:

Acrylic bathtubs cool down quite quickly. In order to make a structure similar to cast iron in terms of thermal conductivity, you need to blow out its sides with foam.
Makes a lot of noise when water fills the bathroom.
Unreliable and flexible at first glance. This visual effect is created due to the small thickness of acrylic. In fact, such bathtubs can withstand both a large volume of water and the weight of a person.

The most important thing is to install the bathroom correctly and securely. To do this, it is placed on legs and additionally fastened with hooks. This is done using brickwork.

Dimensions of acrylic bathtubs of standard and non-standard models

For a very long time, consumers could only rely on cast iron and steel bathtubs. But with the advent of polymer materials, everything changed. These models quickly became popular among consumers.

Conventionally, these baths are divided into four categories:

Small acrylic bathtubs. Thanks to such small dimensions, it fits well into the interior of almost any bathroom. The main disadvantage is the short length of such a bath; its dimensions allow water procedures to be performed only in a sitting position. For greater comfort, such plumbing is not suitable.
Medium-sized bathrooms are suitable if a person likes to take a bath in a reclining position. Such designs are suitable if the room has a non-standard layout. The depth of the tank can be completely different, but the average height is 0.6 m.
Large acrylic bathtubs. They are superior to previous models in terms of convenience, but at the same time they have some nuances. Such structures can only be installed in large bathrooms. It will take a very long time for water to fill such a bath.

Ways to get out of the situation

Firstly, it should be clarified that reducing the bathtub is radical, but it is not the only way to solve the problem. The following points are worth considering.

If the above methods do not suit you, there is nothing left to do but cut out the bathtub. We will look at how to do this correctly and with less losses below.

Underwater rocks

What to do after the sawing work has been carried out and how to protect yourself from possible negative consequences?

Due to a decrease in the rigidity of the edge on the cut side, during operation there may be some disruption of the bathtub geometry, as experts call LED. In this case, experienced craftsmen advise installing the bathtub on standard legs and on a durable frame.
The required edge stiffness can be restored using the fiberglass repair kit and epoxy bumper mentioned above. You need to glue them not with a cut, but with the inner surface of the fold of the edge of the bathtub, by 1-2 centimeters. This will help create additional edge support.
Can be attached to the wall from the undercut side, aluminum profile or wooden block. The side of the tub will rest on them. This will increase the rigidity of the entire structure.

READ Which Hacksaw Is Better For Cutting Trees

It's worth remembering that cutting the bath will void your warranty. Unfortunately, nothing can be done about this.

Advantages and disadvantages of an acrylic bathtub

The sanitary acrylic used to produce this product is a high-tech material. The inserts inserted from it have:

Light weight;
High heat dissipation;
Great mechanical strength;
Sound absorption when cleaning water;
Low cost.

Improper handling of such material leads to surface damage, scratches or melting very easily, so caring for the product requires compliance with the following rules:

Do not use abrasive or aggressive cleaning products;
For cleaning, use only a sponge that is soft on all sides;
Avoid contact with coloring products and chemicals such as hair dye.

Can an acrylic bathtub be drilled, trimmed or sawed?

When renovating a bathroom, many are faced with the question: what to do with an old bathroom? Nobody wants to deal with the hassle of dismantling a heavy cast iron container.

Modern technologies make it possible to simply update it without unnecessary dirt and dust, using an acrylic insert. (rearrange the sentence, breaking it into two separate ones).

Advantages and disadvantages of an acrylic bathtub

Plumbing acrylic, which is used to produce this product, is a high-tech material. Inserts made from it have:

Light weight;
High heat transfer;
Great mechanical strength;
Sound absorption when collecting water;
Low cost.

Another big plus: bacteria do not multiply on the acrylic surface. This is a very important quality for plumbing products.

Improper handling of such material leads to damage to the surface; it is very easy to scratch or melt, so caring for the product requires compliance with the following rules:

Do not use abrasive or aggressive cleaning agents;
Use only a sponge that is soft on all sides for cleaning;
Avoid contact with coloring products and chemicals such as hair dye.

Important addition! In order to determine whether or not it is possible to install an acrylic insert in your bathtub, you must consult with a good specialist. This is due to the fact that these products are not produced for all types of containers.

Why and how to drill, saw and trim an acrylic bathtub

Initially, the liner does not have holes for draining and overflowing water. Naturally, they need to be made, or more precisely, drilled.

This is done with a regular drill or cordless screwdriver using a drill with a diameter of 5 mm and a special crown for holes in wood or stone. Its diameter should coincide with the circumference of the drain and overflow.

To ensure that the holes line up perfectly, place the liner in the main container and mark the centers of the drains. Then align the drill bit with the center and drill the part from the outside and then from the inside. The revolutions should not be made too high.

Why and how to drill, saw and trim an acrylic bathtub

At first, the insert does not have holes for draining and pouring water. Naturally, they need to be done, or rather. Drill.

This is done using a regular drill or a cordless screwdriver using a 5mm drill and a special bit for holes in wood or stone. Its diameter should correspond to the circumference of the drain and overflow.

To ensure the holes are perfectly aligned, place the liner in the main container and mark the centers of the drains. Then center the drill bit and drill through the piece from the outside and then from the inside. Turns should not be too large.

After drilling, sand the edges with fine sandpaper.

The acrylic insert can be compared to a jar lid. It has sides that go along the edges of the container. If the bathtub fits tightly against the walls, then these sides must be trimmed or cut.

Tools you can use:

Electric grinder;
Electric jigsaw;
Electric hand-held circular saw with corresponding saw diameter.

When cutting edges with a grinder, we use cutting discs for any metal 1 1.6 mm thick.

Using a jigsaw, install a special saw with a fine thread, then the cut will be cleaner.

Before you start cutting or sawing , take very precise measurements and mark them on the sides of the insert using a felt-tip pen. The liner should fit perfectly into the container, maintaining uniform contact between the edges and the wall.

Cut with a clear, confident motion to avoid jittery, wavy edges.

You may have decided to remove your old bathtub to install tile behind it. In this case, it is better to install the acrylic insert without cutting. Then deformation can be avoided, and in no case will water get under the liner. This will increase its service life.

If you want to get a new, beautiful, practical and comfortable bathroom without spending a lot of extra effort and money, make an acrylic bathtub using an insert. It will serve you for a very long time.

Is it possible to wash an acrylic bathtub with Sanox?

Leading detergent manufacturer Stork produces Sanox gel, made using the latest cleaning formula. When figuring out the best way to clean an acrylic bathtub, it is worth noting the main advantages of Sanox, which include its disinfecting properties and effectiveness in combating various contaminants. Thanks to the high concentration of active ingredients, you can save a lot on cleaning costs. To care for an acrylic bathtub, apply the gel to the dirt for 10 minutes and then use a sponge to go over the surface.

Is it possible to wash an acrylic bathtub with washing powder?

List of products that should not be used alone to care for acrylic products, including laundry detergent. The thing is that there are small solid particles in it, and they can scratch the surface, and the bathroom will get dirty even faster. For those wondering how to clean an acrylic bathtub, home remedies need to be chosen carefully, and in the case of powder, can be used to prepare a soap solution that removes minor stains.

Is it possible to wash an acrylic bathtub with citric acid?

A safe folk remedy that works well against lime and whitens. Citric acid. With proper care, the acrylic bathtub is cleaned according to the following scheme:

Dissolve the acid in water, taking into account that there should be one standard sachet for 2 liters of liquid.
Soak a sponge in the prepared solution, treat the stains and leave for 20 minutes.
After this, repeat wetting and treat the base surface. All that remains is to wash everything off.

Detergent for acrylic bathtubs Avuar

AVUAR produces high-quality household care chemicals, but it is important to note that phosphate-free warehouses are allowed for acrylic bathtubs. They are sold in concentrated form, so they work well with various types of dirt. Detergent for acrylic bathtubs is applied for 5 minutes. On the dirt and then rub with a sponge. If the spots remain, you can repeat the treatment.

Is it possible to wash an acrylic bathtub with Pemolux?

How to trim an acrylic bathtub

Valentin Vedensky

Can an acrylic bathtub be trimmed? Cutting the stiffeners is not allowed; when filling the bathtub, it may burst under the load; the decorative screen can be cut. You can trim, you can cut, but it’s better not to click with the “beak” We cut, we know, everything can be trimmed if you want, then it’s better to glue a block for reinforcement or when installing, put a thread in it. I saw how a would-be tiler cut cast iron, and hello acrylic ( there’s just one thing, cast iron is cast iron, and acrylic ones are held in place by stiffening ribs)

Irina Lopatkina

Due to the crisis, we cannot do a full renovation of the bathroom. But we want to insert an acrylic liner into an old cast-iron bathtub. Problems with insertion - the size of the bathtub decreases. because the acrylic liner is placed on a special foam; The finished acrylic liner may not exactly fit your bathtub in size. If the technology is violated, the liner may... We didn’t do it. But I saw a question about what to do if after a year the acrylic in the bathroom began to crumble and bubble. So I wouldn't risk it.

Peter Geranin

It is necessary to trim the acrylic bathtub along the edges, asymmetrical. There is such a thing as a stiffener - it is unknown what the bathtub will turn into.

Lev Lagunov

Tell me how to shorten and trim the side of an acrylic bathtub? An acrylic bathtub can be sawn with a regular hacksaw blade for metal. Only then must the cut itself be cleaned and polished. Only then can the aesthetic appearance be preserved. With a string or wood burner

Alena Ezhova

It’s a new bathtub, but the enamel has already worn off and become like sandpaper. How to make a glossy surface? Most likely this is the result of cleaning the bathroom with educational products such as Pemo Lux. It is unlikely that it will be possible to return the enamel to its previous state. Was it new 25 years ago? Maybe this is how it should be, I remember I was at camp with a friend whose parents gave him some blue cheese, so we cut it off. What do you use to wash it with? If it is truly new, then demand that the store fulfill its warranty obligations.

Alena Terebova

I've heard that the bottom of shower stalls cracks after a while. Share your experience - which one is better to install? Well, if you don’t take guys into the cabin, then it serves for a long time and properly, but in general they are made of thin material, I don’t remember exactly - some kind of fiber, so when buying, inspect the bottom, the more stiffening ribs, the more guys the cabin can withstand. Those who don’t have toenails will crack. trims

Vadim Okunev

I'm renovating the bathroom. I bought an acrylic bathtub. She's plastic! easy to cut down. Well, or gouge the walls and level them again. Replace the bathtub or paint new walls. I don’t recommend shortening! Acrylic, of course, is cut with a hacksaw. But, the edges of the bathtub are curved down, and when you cut it, I would try to change the bathtub to a smaller size, or redo the wall in the bathroom. Otherwise there will be no “saleable appearance”, some...

Albert Yasaulov

Is it possible to cut the corner of an acrylic bathtub by 4cm? in a semicircle without losing the rigidity of the bathtub and what is the best way to cut? Isn't it easier to crash into a wall? This is me as one of the solutions. And the stiffness will not be harmed and the procedure is quick and painless. Using a grinder, carefully cut through a wall or tile by 3 cm and that’s it. It’s still a corner for... Carefully use a grinder on both sides. If you are going to cut off the stiffener itself, of course the stiffness will be lost: after all, at the factory they calculate how long and how wide to make this or that stiffener!

Kirill Proskuryakov

We bought a bathtub, it doesn’t fit 3 cm, is it possible to cut it? I specifically bought it in a larger size and am very pleased. They built it into the wall, but there was more space in the bathtub. Of course, breaking is not building! Cut it with a grinder! Or knock down the walls! It’s better to make a groove in the wall. It’s better to change it. No need, gouge the wall ( Make an exchange. You can. Just clean the cut edge from scale and paint the car with enamel, not from a spray can.

Daniil Sosnin

In my bathroom, a 170 bathtub just barely fits in two places on the wall. Do the tiles interfere with making a smaller bathtub? Maybe make grooves on the tiles. Don’t touch the bathtub, it’s better to slightly damage the wall. We also didn’t have room for the sink next to the stall, so we made a recess in the wall, and it worked out really well. Estimate the thickness of the wall (depending on how much it won’t fit. Just estimate it exactly. Or maybe the tiles will be damaged a little.

Anatoly Sverdl

How to properly seal the gap between the bathtub and the wall? If it lasts forever, then make something like a canopy; if there is a small hole, they sell plastic tapes like this. There are ceramic borders on sale, usually white, you can put them, for example, on liquid nails, this will last a long time. If without any problems, the sanitary sealant will last for a year, then fungus will begin to appear, which means... There are no rules. They close up whatever they can. Yes, and what to seal depends on the width of the gap. But there is still one rule for all these non-rules. You need to seal it hermetically, and for acrylic bathtubs also with plastic materials (silicone...

Lyudmila Zhadnova

How to properly lay tiles on a bathroom wall and what is needed for this? In order not to buy extra tiles, its consumption is determined as follows: measure the area of the cladding and divide it by the area of one tile. You get the number of pieces, but it must be increased by 10 percent. You will need: a hammer, pliers, a trowel. For this you need a master tiler. On the website https://stroi-sam1.ru The articles include the article Laying tiles on the wall. Read it, maybe you'll learn something.

Vitaly Vargasov

How to restore a cast iron bathtub? Now there are three ways. 1-enamel: Cons - the most short-lived. The quality of work depends on the qualifications and conscientiousness of the craftsman. Warranty is usually one year. although I renovated the bathtub a couple of months ago... Order an acrylic liner with a copper sledgehammer I painted mine with regular enamel with a roller - it lasted for more than a year. And the special imported enamel lasted a month(

Vadim Bobchikhin

How should you treat gypsum plasterboard in the bathroom before laying tiles? Read at the same time about other types of finishing: SP 55-101-2000 CODE OF RULES FOR DESIGN AND CONSTRUCTION ENCLOSING STRUCTURES USING GYPSUM CARDBOARD SHEETS 6.8 Finishing the surfaces of partitions and suspended ceilings made of plasterboard... But you don’t have to process it Anyway, everything will fall off soon. If you spill water on the floor, it will be absorbed along the seams of the floor tiles into the bottom of the gypsum wall. There are 5-10 such cycles and the tile adhesive is weakened, it is only glued to the paper...

Acrylic bath care products

Is it possible to clean an acrylic bathtub with a Sif?

Ideal for plumbing maintenance Cif, which can be purchased as a cream or spray. The first option is more popular. If you are wondering the best way to clean an acrylic bathtub, then know that Cif is versatile and can handle a variety of stains. It contains micro mineral granules and biological additives that remove various stains and rust. It is better to apply Sif to the dirt, leave for 5-10 minutes, then rub with a sponge and rinse.

Is it possible to wash an acrylic bathtub with vinegar?

Table vinegar. Popular household cleaning product. It removes rust and lime. Care for an acrylic bathtub is carried out as follows:

To whiten and remove plaque, you can only use 7% vinegar. Add it to the bath using approximately 2 liters of solution. It should be left until 10:00, but no more. If these rules are not followed, microcracks may appear.
There is another way to clean an acrylic bathtub from yellowness, for which you prepare 9% vinegar and borax, which is known for its excellent bleaching properties. These components must be mixed in equal quantities. Soak a sponge in the prepared mixture and wipe the dirty areas. When the process is finished, rinse the vessel with clean water.

Is it possible to clean an acrylic bathtub with Domestos?

This manufacturer enjoys authority in the household chemicals market, so many people buy it to care for their plumbing fixtures. As part of Domestos there is hydrochloric acid, which copes well with various contaminants. When describing whether a Domestos acrylic bathtub can be washed or not, it is worth mentioning other advantages of this tool: safety, reasonable cost, efficiency and no risk of damage to the surface. Apply the gel to a sponge, walk through the dirt and leave for 5 minutes, then rinse with plenty of water.

Sources:

https://comfortdo.Ru/mozhno-li-podrezat-akrilovuyu-vannu-po-dline.Html https://zaokskiylesorub.Ru/vanna/mozhno-li-podrezat-akrilovuyu-vannu-po-dline https:// remontkd.Ru/poleznye-sovety/mozhno-li-sverlit-akrilovuyu-vannu.Html https://womanadvice.Ru/uhod-za-akrilovoy-vannoy-kak-derzhat-ee-v-chistote