If problems arise in the operation of the old faucet, and purchasing a new one is not planned, there is no other choice but to disassemble the faucet in the bathroom. In most cases, it is possible to restore nodes on your own. After disassembly, you can see which parts have worn out and require replacement.
In most cases of problems with the mixer, you can fix it yourself by disassembling the structure.
Design of single-lever models
A distinctive characteristic of this type of mixer can be considered a lever that simultaneously performs the functions of two heads at once. With its help, the temperature and pressure of the supplied jet are regulated.
In the first case, the tap handle moves to the right or left, in the second - up or down. Typically, these processes are combined, allowing the user to set the option that is most comfortable for him.
The design of single-lever accessories is extremely simple. Typically such a device consists of the following parts:
- body – can be made of different materials;
- spout - depending on the purpose of the tap, it can be low, high or medium;
- switch - a lever with which the temperature and flow strength are set;
- cartridge – for regulating the flow of water, which is an analogue of a faucet axle box.
In addition, single-valve devices also use service elements, such as gaskets. Often such accessories are also equipped with additional components that increase comfort of use. Among them are aerators that saturate the flowing stream with air, built-in dispensers for detergents and much more.
Single lever faucets can be made from a variety of materials. Chrome-plated models have become especially popular, but on the market you can also find accessories made of copper, brass or granite imitation
Installation of a new mixer (wall and floor models)
When installing a new device, proceed as follows:
- inspect the eccentrics. These are bushings screwed onto pipes, one part of which is slightly offset relative to the other. They allow you to set the center distance to the size of the mixer (usually 15 cm), because it is quite difficult to give such an exact position to the pipes. Eccentrics in good condition are left in place; those in poor condition are replaced. If the mixer has been standing for a long time, it is useful to replace the seal in the pipe-eccentric connections. It could become dilapidated, and then particles of the material will pollute the water;
- if necessary, rotate the eccentrics, moving them to the desired position. Everything is done correctly if the distance between the centers of the eccentric holes exactly corresponds to the center-to-center distance for the mixer connecting pipes, and each eccentric is like a mirror image of the second: under this condition, the mixer is located horizontally;
- if necessary, clean the eccentric threads with a wire brush;
- put decorative washers on the eccentrics (wall-mounted mixer);
- wrap a sealant around the threads of the eccentrics. Taking into account the fact that when screwing on the nut it will be distributed further along the thread, slightly more material is placed on the first turns (winding begins from the end);
- wrap the nuts of the new faucet with electrical tape or masking tape so as not to scratch the shiny surface with the wrench;
- manually screw the nuts onto the eccentrics as long as possible;
- having reached the stop, tighten the nuts with an adjustable wrench, turning them a quarter turn;
- remove the masking tape from the nuts and check the operation of the mixer by opening the root valves.
If there are leaks in the connections, they are tightened or repacked after turning off the water.
Locking element options
In models with one lever, two types of units that regulate water flow can be used. Let's take a closer look at their device.
Ball lever
Such a unit is a ball made of stainless steel, in which special holes and fasteners are provided, with the help of which the sleeve with the ball located inside is attached to the structure.
When the lever is turned, the holes on the ball move, blocking or clearing the path for the movement of cold and hot water, thereby regulating the temperature and flow pressure.
Schematic representation of a single-lever valve with a ball functional unit, with detailed illumination of all fastening, safety and other service elements
Lever valves with a ball mechanism are highly resistant to hydraulic shocks.
However, such models have a number of disadvantages, which include:
- relative high cost;
- rapid accumulation of scale on the ball element;
- intensive wear of rubber gaskets.
- the difficulty of repair, which is why you often have to dismantle the old one and select a new mixer.
Due to the listed disadvantages, mixers of this design are used less and less in everyday life and in production. In contrast, ball valves, installed in front of plumbing fixtures on water supply pipes to control the water supply, have almost completely replaced valve models.
Disc crane models
Such accessories are favored by consumers and specialists. The operating mechanism of such mixers is ceramic disc cartridges, similar to ceramic disc mechanisms that are used in two-valve devices.
The disk mixer, a schematic representation of which is shown in the figure, is considered a more practical functional model, since it allows cartridge replacement
Externally, this element looks like a plastic cylinder, usually blue. However, hidden under the body are two plates made of snow-white, carefully polished ceramic. One of these disks can move depending on changes in the position of the lever.
In order for water to flow into the spout, the holes on the upper and lower parts must match. If this does not happen, the flow is blocked and does not enter the tap.
Disc models have a number of advantages:
- moderate cost;
- the ability to replace cartridge elements, which facilitates repairs;
- reluctance to form scale, which hardly accumulates on ceramic surfaces.
The weak point of such structures is their sensitivity to foreign inclusions in the water flow, as well as to sudden pressure surges in the water network.
The cartridge discs are made of well-polished ceramic, which ensures a good fit. The service life of mixers largely depends on the quality of these parts.
Instructions for dismantling the faucet in the bathroom
- Completely turn off the main taps that supply the bathroom or the entire facility (apartment, house), release the residual pressure in the system and drain the remaining water in the pipes by moving the mixer control to the open position. If water-intensive equipment (boiler, boiler) is connected to the water supply system, it is necessary to turn off the valves on them as well.
- We unscrew the fastening nuts of the dismantled mixer using an adjustable plumbing wrench. In some cases, it will not be possible to perform this operation manually; then you should lightly tap the hammer on the handle of the tool to remove the “sticking” nut.
- Inspect the eccentrics. Typically, these connecting elements are quite durable, but if traces of corrosion processes are detected, they must also be replaced. Sometimes you can restore the thread by running it a couple of times with a half-inch die.
NOTE! If it is necessary to replace the eccentrics, they must be dismantled as carefully as possible, slowly, in order to avoid damage to the threads on the fitting.
To perform this operation, use pliers (pliers) by inserting one of the jaws of the tool into the hole, squeezing the handles and turning in a counterclockwise direction. If it is difficult to unscrew and you can get it with an adjustable wrench, you can use it.
How to disassemble a lever device?
To repair models with one locking mechanism, it is necessary, first of all, to disassemble the structure in order to remove the damaged element. It is replaced with a similar new part. Repairing a lever mixer is quite easy, but you need to act very carefully.
Disassembling a disk product
To dismantle the accessory, you will need a set of the following tools - a screwdriver and a hex key.
The following algorithm of actions is used:
- First of all, you need to shut off the hot/cold water pipes.
- You should free yourself from the plug, which can be removed with a screwdriver.
- Using a hex key, unscrew the screw part that connects the lever to the rod, where the water is regulated.
- Having done this, you can manually remove the crane lever. Then you need to unscrew the ceramic nut, as well as the clamping nut that secures the top plate.
This allows access to the mixer disc. You can take it out and insert a new cartridge into the resulting space, but you need to ensure the correct position of the holes on this part.
After which all operations are carried out in reverse order. Having assembled the faucet and completed the manipulations, you can turn on the water to check the correct assembly.
When going to the store to buy a new cartridge, it is advisable to take the failed disk. Models may differ in the diameter of the holes available and the fasteners located on the bottom edge of the products. It is better to give preference to cartridges with a silicone gasket, as they are better resistant to water.
Disassembling the ball mixer
A similar process is performed in the same way as described above, but there are some nuances. First of all, you also need to turn off the water. After this, using a screwdriver, the decorative plug is removed, the fixing screw is unscrewed and the nut that holds the faucet mechanism in the correct position is removed.
It is worth keeping in mind that if the ball accessory is seriously damaged, the entire mixer will have to be replaced. Repair of the ball device is only possible if the problems are caused by a worn out rubber gasket or the faucet being clogged with abrasive materials.
In some faucet models, the handle fits quite tightly into the control rod. To release the part, it is recommended to carefully pry it off with the end of a screwdriver.
Constantly dripping water from the faucet usually indicates problems with the gasket.
To resolve the issue, you need to take the following steps:
- As described above, the screw is unscrewed and the lever is removed.
- The connection is removed from the thread, after which the screw is unscrewed with a screwdriver. If plaque is found on it, it must be carefully removed with a soft cloth.
- The ball is removed from the structure, after which the worn gaskets are carefully removed and replaced with new parts.
- Upon completion of the process, the ball is put back in place, and the seals are attached using a plastic nut.
- The lever is placed again, and then the screw that secures this part is screwed in.
After completing these operations, the crane is checked.
Problems with the ball mixer being clogged are indicated by a thin stream of water even with the tap at maximum pressure.
In this case, you need to follow the following instructions:
- unscrew the nut from the mixer spout;
- remove the mesh and rinse it thoroughly with water;
- insert the part back, and then re-tighten the nut.
If the manipulations described above did not help solve the problem, you need to replace the device and install a new faucet in the kitchen or bathroom.
Particular care must be taken when loosening and tightening the locking nuts. Excessive force can easily damage the elements.
Types of faucets
There is a huge selection of mixers. Different types and sizes. They also differ in the fastening and design itself. The price range is very wide, since it takes into account not only what and how the mixer is made, but also the manufacturer. How to change a bathroom faucet inexpensively?
Faucets designed for bathtubs have a mechanism that switches water from the tap to the shower, and also have an additional outlet where the shower hose is connected. All faucets have two valves and a solid body, differing only in the mechanism that switches the water.
Their differences are as follows:
Eccentric mechanism. This mechanism is the most common. By turning the handle, you activate the rod, which closes one of the openings for the shower or spout. It is very easy to use and low cost. Its features: the gaskets wear out quickly, however, if they break, they can simply be replaced.
Cartridge mechanism. It is similar in design to a cartridge for a lever mixer. Its dimensions are smaller, but it works the same way, closing and opening holes for water. It lasts a long time and is hard to break. It is easier to change than an eccentric mechanism. However, if the cartridge breaks, you won’t be able to simply replace the faucet in the bathroom; the entire faucet will have to be replaced.
Ball mechanism. The mechanism is based on a brass ball with holes machined perpendicularly. When turned, it is fixed in one of the positions, and water flows into a certain hole. He is the most reliable. But if it breaks, you will most likely have to change the faucet in the bathroom.
There are also removable mechanisms. They can also be related to the topic of replacing a bathroom faucet. Unfortunately, here you cannot simply change the faucet in the bathroom, since the design is cast. There are cork or rotary ones. Rotary mechanisms are simpler and more convenient. If a breakdown occurs, you need to remove the plug and install a new one; disassembling the structure itself is not provided.
Prevention of breakdowns of single-lever models
Since replacing a faucet is quite expensive, you need to think about simple preventative measures that can extend the working life of this important part.
These include:
- regular inspection of mixers to identify the slightest signs of leakage;
- installation of filtering equipment to improve water quality;
- elimination of high humidity in places where plumbing fixtures are located.
Before independent installation or dismantling, and even more so before carrying out repairs, you must carefully study the structure of the mixer and the instructions and strictly follow the instructions. All connecting nodes must be sealed with special compounds or fum tape to avoid leaks.
The condition of the tap is positively influenced by the aerator, which mixes water with air. If the model does not have a built-in device, it can be purchased separately and installed on the mixer
It is also important to take a responsible approach to choosing models for the bathroom or kitchen. When purchasing a faucet, it is better to avoid silumin products made from an alloy of aluminum and silicon. Although such models are inexpensive, they quickly break down.
It is better to give preference to models made of brass, copper or chrome-plated steel, produced by well-established brands.
What tools and materials are needed to replace the faucet?
Before changing this element of the plumbing system, you need to prepare the following tools:
- adjustable wrench;
- pliers or pliers;
- a set of screwdrivers (slotted and Phillips);
- half-inch die for restoring external threads;
- You may need a hammer to dismantle the old faucet.
You should stock up on these materials:
- fum tape for sealing threaded connections or regular linen tow;
- sealant;
- rubber, silicone or paranitic gaskets (usually included with a new faucet);
It is possible that new eccentrics may be required. It will not be superfluous to keep a bucket on hand to drain water from the system (especially if it is impossible to completely close the valves on the inlet sections of the pipes) and a rag.
The best manufacturers on the market
Modern single-lever models are very popular, which is why they are presented in the collections of leading companies engaged in the production of plumbing accessories. Among the most famous brands belonging to different price categories are the following.
GROHE – wide functionality and high quality
None of the faucet ratings is complete without models from the German brand Grohe. Despite their rather high cost, they have earned the attention of consumers with their modern design solutions, durability and reliability.
Accessories of this brand are often equipped with many additional options, which ensures comfortable operation. Among the wide range of single-lever kitchen appliances, users most often note the Concetto 32663001 model with a 45-centimeter pull-out spout, which practically replaces a pull-out watering can.
The faucet uses a virtually silent aerator and a reliable SilkMove ceramic cartridge. A popular model for the bath is the Euroeco 32743000 faucet with an aerator and a special water saving regulator.
Grohe faucets and other accessories have a classic design, making them easy to fit into any room design.
LEMARK – original solutions
The Czech company produces mainly single-lever products with a high spout, which are convenient to use in the kitchen. Sometimes they also have a built-in dispenser into which liquid detergents are poured. The models are available in a wide range of shades, which allows you to choose the faucet to match the color of the sink.
At the same time, the catalog also presents traditional chrome-plated products, which serve as a universal option. The top best models according to users included the Comfort LM3061C kitchen mixer, as well as the Pramen LM3318C shower unit.
Owners of these devices note the impressive design of the devices, thoughtful design and high quality. Some claim that they have been using Lemark accessories for several years without any repairs.
Lemark single lever faucets are often equipped with additional accessories and fixtures, such as a pull-out shower head, for added ease of use.
OMOIKIRI – Japanese technology
Plumbing accessories from the Japanese brand “Omoikiri” impress with their unique design, as well as the highest quality and long service life. The manufacturer provides a five-year warranty on all products. Many models have a double spout, thanks to which tap water is supplied separately from drinking water.
The rating of the best models for the kitchen includes the Tonami-C single-lever mixer, made of lead-free chrome-plated brass. The accessory has a double spout with a 360° rotation angle and a built-in aerator. At the same time, users note the reliability and durability of the crane.
Although the cost of Omoikiri products is quite high, users consider it justified. The models are distinguished by their reliability, long-term operation, and original appearance.
IDDIS is the best Russian manufacturer
The products of the Russian company are very popular due to their diverse range and affordable price. They are also of acceptable quality and, with proper care, can last up to 5-7 years without repairs.
Among the accessories that have earned high user reviews, we can note the universal single-lever faucet IDDIS Vane VANSBL0i10 with a swivel spout, a retractable head with a square shower, and an aerator nozzle.
The reliable and simple kitchen faucet Alborg K56001C is also popular. Due to its low spout, this model is best used in shallow sinks.
IDDIS models usually have a classic design and a chrome-plated surface, making them a perfect match for common stainless steel sinks
KAISER – German quality at an affordable price
The Kaiser brand produces a wide range of faucets that have different types of spouts - pull-out, stationary, rotary, flexible. The products are distinguished by their magnificent appearance, while their cost is quite affordable.
Among the presented models, users especially noted the Kaiser 13044 kitchen faucet with a body made of high-quality brass.
In addition to its excellent appearance, this sanitary accessory has two built-in aerators and a water filter. The high spout has the ability to rotate 360 degrees, which guarantees easy access to all corners of the sink.
Kaiser catalogs present not only traditional chrome options, but also stylish accessories made in bronze or granite.
Installation on a bathtub or sink
The devices are connected to the water supply via a flexible connection and operate as follows:
- a hole with a diameter corresponding to the size of the mixer is drilled in the side of the bathtub or washbasin. To form such holes, crowns (cylindrical drill) are used, and if such a tool is not at hand, many holes are drilled along the contour with an ordinary drill and then the spaces between them are broken with pliers;
- Place the gasket on the side and install the mixer, threading the connecting pipes into the hole. The device is secured from below with a horseshoe washer and nut (a gasket must be put on first);
- connect the mixer pipes and pipes with a flexible liner. There is no need to seal the connections - the liner nuts already have gaskets. To avoid crushing them, excessive tightening is contraindicated.
If the flexible liner leaks, it is not necessary to completely change it: videos have been published on the Internet with instructions for installing a cracked polymer tube inside the braid. Repair is significantly cheaper than buying a new product.
Conclusions and useful video on the topic
The video below describes in detail the structure of a single-lever mixer, its disassembly and correction of the most common breakdowns:
Single-lever faucets are a modern type of plumbing fixture that has gained popularity due to its excellent consumer properties. The advantages of such devices include a long service life and ease of maintenance.
The ability to correctly disassemble an accessory will help you quickly replace a failed part. Thanks to this, the service life of an expensive product is extended and there is no need to replace it.
Would you like to talk about how you selected or repaired a single-lever faucet? Do you want to share your own experience as a novice plumber that might be useful to site visitors? Please write comments, ask questions, post photos in the block below.
